Replacement Membrane for PS-PURUF / PS-UFPOU1 / PS-PH200 Ultrafiltration Systems

Replacement Membrane for the PS-PURUF Ultrafiltration System and PS-PH200 Ultrafiltration + Alkaline System

This 0.02 micron replacement ultrafiltration membrane is easily installed in the Premiere PS-PURUF ultrafiltration system (previously called PS-UFPOU1) and Premiere PS-PH200 ultrafiltration + alkaline system. (Read more these drinking water systems below). The membrane is the module on top of the metal bracket of the system. This ultrafiltration membrane is the workhorse of the PS-PURUF and PS-PH200 system – it remove particulates and solids like bacteria, viruses, protozoa, and colloidal materials on a microscopic level. Easily backflush (clean) this membrane by turning the valve on your PS-PURUF or PS-PH200 system. Backflushing is good for this membrane – it helps prolong the life. Extra long membrane life up to 3 years. Maintains naturally occurring minerals for health and taste.

• 0.02 micron UF membrane – Filters out solids / particulates as small as 0.02 micron including: bacteria, protozoa, cysts, viruses, algae, dirt, mold, silt, colloidal silica, clay, iron, sand, lead particulate, and more.
• Operates smoothly under low pressure – up to 1.5 gallon per minute flow rate depending on incoming water pressure
• Zero waste water during the purification process. A conventional reverse osmosis system may waste 3 – 25 gallons of water to produce one gallon of reverse osmosis water. This membrane is revolutionary in that is does not waste water in the production of purified water.
• Back flushing membrane ensures longer water membrane life. When a membrane undergoes a backward flush, its pores are flushed inside out to clean it of contaminants. Innovative technology lets you flush (clean) the membrane whenever it gets full of contaminants. You can tell when it’s time to flush the membrane because there will be a drop in water pressure. Simply turn the valve to flush the membrane (please note that a small amount of water will be discharged while the valve is open). Membrane should be replaced every 2-3 years.
• Easy installation in the PS-PURUF or PS-PH200 system – Module membrane with an inlet and outlet (3/8″) and flush port (1/4″) that easily connects to your Premiere PS-PURUF or PS-PH200 system to replace the used one

• Flow rate: up to 1.5 gallons per minute (depends on your incoming water pressure)
• Operating pressure: 35 psi – 85 psi

Special notes:

1. Total dissolved solids (TDS): This product is NOT recommended for water with a high TDS level (over 500 ppm) or if you wish to reduce/remove TDS. The ultrafiltration process preserves healthful minerals (minerals make up TDS). If you have a TDS level above 500 ppm or wish to reduce/remove your TDS level, please keep in mind that only reverse osmosis and deionization will reduce and remove TDS in water. Here's a reverse osmosis drinking water system. Read about total dissolved solids.
2. Taste: If you want to achieve “tasteless” water that is free from minerals and TDS, (i.e., how some bottled water tastes – or doesn’t taste, rather) you will want to consider reverse osmosis because ultrafiltration preserves healthful minerals and doesn't reduce or remove TDS, which can contribute to how your water will taste.
3. Water softeners: Do not use this membrane with water softeners that use sodium (salt). This is because some water softeners make hard water “soft” by replacing the calcium and magnesium with sodium. These high levels of sodium break down the membrane.
4. Filter life: The life of the UF membrane and filter cartridges may vary according to water quality, water usage, flow rate, and inlet line pressure which may require more frequent membrane flushing and replacement of the membrane and cartridges.
5. Flow rate: May vary depending on water pressure, water temperature, local water conditions, and how full the membrane is.
6. Additional parts: Since plumbing configurations can vary, you may need to supply additional parts or adaptors in order to connect this system to your plumbing.

Please note that this membrane is NOT recommended for water with a high TDS level (over 500 ppm) or if you wish to remove all TDS, or for use with water softeners that use sodium (salt).